Posts Tagged ‘DNOS’

Dell Force10 Part 1: Initial Configuration

July 3, 2016

force10_S4048_on
When it comes to networking Dell has two main series of switches. PowerConnect/N-series, which run DNOS 6.x operating system. And S/Z-series switches, which run on DNOS 9.x derived from Force10 OS (FTOS). In this series of blogs we will go through the configuration of Force10 switch series and use Dell S4048-ON top of the rack switch as an example.

Interesting to note, that unlike other S-series switches S4048-ON is an Open Networking switch. Dell is one of the first companies which apart from its own OS lets customers run other operating systems on its network switches, such as Cumulus Linux OS and Big Switch Networks Switch Light OS. While Cumulus and Big Switch has its own use cases, in this blog we will look specifically at configuring FTOS.

Boot process

S4048-ON comes from the factory pre-configured for bare metal provisioning (BMP). This is what you will see when you boot the switch for the first time:

s4048_bmp

If you just want to boot FTOS, simply skip the BMP by choosing A and switch will boot the OS.

After some time BMP will time out. If you’ve missed the above wizard, you can also disable BMP from CLI using the following commands:

> enable
# stop bmp
# config
# reload-type normal-reload
# exit
# reload

When prompted choose to save the configuration and proceed with reload. After the switch has rebooted check that the next boot is set to normal reload:

# show reload-type

Initial configuration

First steps of any switch installation is assigning a hostname and management interface settings:

# hostname DELL4048-SWITCH
# int managementethernet 1/1
# ip address 172.10.10.2/24
# no shut
# management route 0.0.0.0/0 172.10.10.10

Then set admin / enable passwords and allow remote management via SSH:

# enable password 123456
# username admin password 123456
# ip ssh server enable

Configure time zone and NTP:

# clock timezone UTC 11
# ntp server 172.10.10.20
# show ntp associations
# show ntp status
# show clock

Firmware upgrade

Force10 switches have two boot banks A: and B:. It’s a good practice to upload new firmware into one boot bank and keep the old firmware in the other in case you need to roll back.

The easiest way to upgrade is via TFTP using Tftpd64, which you can download for free from here. If you’re upgrading an existing switch, make sure to save the running config and make a backup. If it’s an initial install you can skip this step.

# copy run start
# copy start tftp://10.0.0.1/FORCE10_SWITCH_01.01.16.conf

Then upload new firmware to image B:, change active boot bank to B: and reload:

# show version
# show boot system stack-unit 1
# upgrade system tftp://10.0.0.1/FTOS-SK-9.9.0.0P9.bin b:
# conf t
# boot system stack-unit 1 primary system b:
# exit
# reload

You will be prompted to save the configuration and reboot. After the reboot you may be asked to enable SupportAssist. SuppotAssist helps to automatically open Dell service tickets if there is a switch fault. You can enable SupportAssist by running the following commands and answering prompts:

supportassist

# conf t
# support-assist activate
# support-assist activity full-transfer start now
# show support-assist status

My pair of switches were configured in a Virtual Link Trunking (VLT) domain. I’ll explain how VLT works later in the series. But from the upgrade point of view, each switch in a VLT domain is treated as a separate switch and has to be upgraded separately. If you decided to use a stack instead of VLT, you can find the upgrade process for a Force10 stack in my other post about Dell MXL switches here.

Spanning tree

Spanning Tree Protocol (STP) helps to prevent network topology loops and is highly recommended for use in any network. Switches connected in an actual loop topology in today’s networks are rare. But STP can save you from consequences of a potential human error, such as port channel misconfiguration. If instead of creating one port channel with two links, you by mistake create two port channels with one link each and both carry the same VLANs, you’ve accidentally created a loop, which will bring your whole network to an immediate halt.

It’s a good practice to enable STP as a safeguard mechanism from such configuration errors. S4048-ON supports STP, RSTP, MSTP and PVST+. In my case S4048s were uplinked into HP core, which supported STP, RSTP and MSTP. If you have Cisco switches in your network core you can use PVST+. In my case I used RSTP, which is a good choice if you don’t require enhancements of MSTP and PVST+ in your network. Just make sure to not use the basic STP protocol, as it provides the slowest convergence.

# protocol spanning-tree rstp
# no disable
# show spanning-tree rstp

In every STP topology there is also a root switch, which by default is selected automatically. For a more deterministic STP behaviour it’s recommended to select the root switch manually, by assigning the lowest STP priority to it. Typically your core switch should be your root switch. In my case it was a HP core switch, which was assigned priority of “0”.

When configuring server and storage facing ports make sure to enable EdgePort mode to minimize the time it takes for the port to come online:

# int range Te1/45-1/48
# spanning-tree rstp edge-port
# switchport
# no shut

If you want to know more about how STP works, you can read a few of my previous blog posts on STP here and here.

Flow control

To avoid dropped packets on 10Gb switch ports at times of potential heavy utilization it is also a best practice to as a minimum enable bi-directional Flow Control on the storage array ports. I enabled it on the iSCSI links connected from the Dell Compellent storage array:

# int range Te1/17-1/18
# flowcontrol rx on tx on

If you specifically interested in switch best practices for Compellent and EqualLogic storage arrays, Dell has a full list of guides for various switches at communitites wiki here.

Port channels and VLANs

Port channels and VLANs are configured similarly to any other switch, but I include them here in case you want to know the syntax. In this example we have two access ports 1/46 and 1/47 and an uplink to the core configured as port channel 1:

# interface port-channel 1
# switchport
# no shutdown

# interface range Te1/1-1/2
# port-channel-protocol LACP
# port-channel 1 mode active
# no shutdown

# int vlan 254
# untagged Te1/46-1/47
# tagged po 1

Keep in mind, that port channels are used either in one switch configurations or when two or more switches are stacked together. If you’re using Virtual Link Trunking (VLT), you will need to create Virtual Link Trunks (VLTs). Which are similar to port channels, but have a slightly different syntax. We will talk about VLT in much more detail in the following Force10 blogs.

Conclusion

One feature which I didn’t specifically mentioned in this blog post was Jumbo Frames. I tend not to use it in my deployments until I see convincing evidence of it making a difference for iSCSI/NFS storage implementations. I did a post about Jumbo Frames long time ago here and hasn’t changed my opinion ever since. Interested to here your thoughts if have a different take on that.

References

Advertisements

Beginner’s Guide to Dell N4000 Series Switches

January 18, 2016

Dell N-Series switches run on Dell Network Operating System (DNOS) version 6.x. Unlike Dell S-Series switches which run on DNOS 9.x, derived from  Force10 Operation System (FTOS), DNOS 6.x came from the PowerConnect switch series and share the same codebase. So if you’ve ever worked with PowerConnect switches, N-Series syntax should be very familiar.

In my case I had two Dell N4032F switches. But the same set of commands applies to any other N4000 Series switch.

Initial Configuration

When you first turn the switch on, it gives you 60 seconds to enter the wizard, where you can set up network settings for the Out-of-Band (OOB) management interface and change the admin password. If you miss it you can reboot the switch and it will show the same wizard prompt again when it boots up. Or you can set it up from the CLI:

# interface out-of-band
# ip address 10.10.10.10 255.255.255.0 10.10.10.254

# show ip interface out-of-band

Once you get to the CLI prompt, configure hostname and enable SSH:

# hostname n4032f-prod

# crypto key generate rsa
# crypto key generate dsa
# ip ssh server
# ip telnet server disable

Stacking

Dell N4000 Series switches support both stacking and MLAG (Multi-chassis Link Aggregation). One of the drawbacks of the stack configuration is disruptive firmware upgrades. When you update firmware on the stack master, firmware is distributed to all stack members and all switches are rebooted simultaneously.

In MLAG each switch has its own Control Plane and can be rebooted independently. Which is MLAG’s shortcoming at the same time, because unlike stack, where all units act as one switch, in MLAG you have to manage each switch separately.

In my case I chose stacking for its simplicity.

Dell N4000

N4000 switches are stacked using the two 40Gb QSFP ports located at the front. QSFP ports are not configured in stack mode by default. Which you need to change on both switches before you can build a stack:

# stack
# stack-port Fortygigabitethernet 1/1/1 stack
# stack-port Fortygigabitethernet 1/1/2 stack

# show switch stack-ports

Once QSFP ports on both switches are configured, disconnect power from both switches and boot the switch you want to be the stack master first (typically the top switch). When the first switch has fully booted, boot the second switch and check the status. This is what you should see:

# show switch

n4000_stack

Firmware Upgrade

If it’s not a brand new switch, save the config before doing the firmware upgrade:

# copy run start
# copy running-config tftp://10.10.10.100/backup.txt

You can use any TFTP server for the firmware upgrade, such as the free Tftpd64 server.

tftpd64

Then you upload the firmware image to the stack master and reload the stack:

# copy tftp://10.10.10.100/N4000v6.2.7.2.stk backup
# boot system backup
# reload
# show version

Firmware is uploaded to a backup image. Then you select the backup image for the next boot and reload the stack. When both switches reboot you should see something similar to this:

frimware_upgraded

As part of the upgrade process the new firmware is automatically uploaded from the master to all stack members, which is a default behaviour. You can confirm it is enabled using the following command:

# show auto-copy-sw

Flow Control, Jumbo Frames and iSCSI Optimization

In my case I used two N4032F switches for an iSCSI backbone, so I needed to make sure that Flow Control and Jumbo Frames are enabled on the switch.

Flow Control is enabled by default, which you can confirm by the following command:

# show storm-control

To globally enable Jumbo Frames on all ports type:

# system jumbo mtu 9216

# show system mtu

Interestingly, Dell N4000 Series switches also have built-in iSCSI optimization, which can detect iSCSI sessions by snooping the traffic on ports 3260 and 860. It then prioritizes iSCSI traffic over the other types of traffic to guarantee low latency for storage I/O. To show iSCSI settings:

# show iscsi

By default switches only track the sessions. Traffic prioritization is disabled by default and has to be enabled manually. This didn’t matter in my case, as the switches were dedicated for storage traffic. But if you share switches between storage and server traffic, you may want to enable it. Refer to the switch User’s Configuration Guide for details.

If you’re using a Dell Compellent storage array with N4000 switches, also make sure to apply a Compellent profile to the ports where storage array is connected to:

# macro global apply profile-compellent-nas $interface_name te1/0/1
# macro global apply profile-compellent-nas $interface_name te1/0/2
# macro global apply profile-compellent-nas $interface_name te1/0/3
# macro global apply profile-compellent-nas $interface_name te1/0/4

VLANs, Trunks and Port Channels

Again, I didn’t use any VLANs and Trunks, because switches were dedicated for iSCSI traffic and were separate from the LAN core. And I didn’t need Port Channels either, as they are not required for iSCSI.

Your scenario might be different. For instance, if you have vSphere hosts connected to a NetApp array over NFS, you may want to create a Multi-Mode (LACP) VIF on the NetApp side. If that’s the case, to create a port channel on the Multi-Mode VIF ports use the following:

# interface range te1/0/2,te2/0/2
# channel-group 1 mode active
# show intefaces po1

If the switches are used for both storage and VM traffic, then you’ll need to configure the server ports and uplink them to your network core. Create your VLANs first:

# vlan 10,20,30

Configure vSwitch uplinks from the ESXi hosts. In a typical vSphere environment, traffic is tagged on the vSwitch side, which means that server ports should be configured as trunks:

# interface range te1/0/3-6,te2/0/3-6
# switchport mode trunk
# switchport trunk allowed vlan 10,20,30

And finally configure uplinks to the network core. Depending on how your LAN core is set up, you may want to create a port channel to the upstream switch and trunk the required VLANs:

# interface range te1/0/1,te2/0/1
# channel-group 2 mode active
# switchport mode trunk
# switchport trunk allowed vlan 10,20,30
# show intefaces po2

Conclusion

This guide didn’t include information on Spanning Tree, QoS or any of the switch Layer 3 features, but I hope it could get you started. At the end of the day, every environment is different. If you need additional information refer to the following guides from the Dell web-site: